Varenummer: | 86-634 |
Varekode: | PP41SW |
Vægt: | 40.2g |
Produkt: | Boks |
Længde: | 100mm |
Bredde: | 50mm |
Højde: | 25mm |
Farve: | Sort |
Materiale: | Plastik |
PP12SW |
![]() |
Features |
• Hand-held enclosure consisting of two shell halves • Lap joint construction • Two lateral guides (stud and bushing) are used to connect both shell halves. • Two cams for self-tapping screws where a printed circuit can be mounted. |
![]() |
PP22SW |
Transmission Receipt Enclosure for a Remote Control |
![]() |
Features |
• Consisting of two shell halves which snap together to connect. • Lap joint construction. • 12V-Battery is required. (GP-23A is suitable and available in our "Components & Devices" catalogue at product group S1138) • The printed circuit is fastened without screws onto a molded stud. • In the upper section, there is a countersunk keypad. • A button actuator is included which lies adjacent to an opening for a LED (You will find suitable LEDs in our Semiconductors catalogue at product group W1222). • The firmly attached plastic button has a stroke of approx. 2mm, e.g. for operating a microswitch which is beneath (not supplied in the delivery). |
![]() |
Dimensions |
![]() |
|
Outer: |
57x36x16mm |
Inner, (Usable)1): |
42x32x9mm |
1) Including Battery Compartment for Round Cells, Contacts are Attached Loosely |
|
![]() |
PP23SW |
![]() |
Features |
• Similar to PP12SW, but with 4 screws composed of stud and bushing placed in the corner to connect both shell halves |
![]() |
PP24SW |
Transmission Receipt Enclosure for a Remote Control |
![]() |
Features |
• Similar to PP22SW but with two button actuators lying adjacent to each other (black/red) and an opening above for a LED |
![]() |
Dimensions |
![]() |
|
Outer: |
57x36x16mm |
Inner (Usable)1): |
42x32x9mm |
1) Including Battery Compartment for Round Cells, Contacts are Attached Loosely |
|
![]() |
PP40SW |
![]() |
Features |
• Black enclosure made of ABS • Lid and base are attached using two studs. • Fastening point for printed circuit |
![]() |
Dimensions |
![]() |
|
Outer: |
50x36x20mm |
Inner: |
46x33x16mm |
![]() |
PP41SW |
![]() |
Features |
• Black enclosure made of ABS consisting of base and lid • Four countersunk screws seal the housing all around. • Four mounting studs for a printed circuit 82x46mm |
![]() |
Dimensions |
![]() |
|
Outer: |
100x50x25mm |
Inner: |
96x46x21mm |
![]() |
PP42WS |
![]() |
Features |
• White sensor enclosure made of ABS • Large louvered plates on either side • Fastening points for printed circuit |
![]() |
Dimensions |
![]() |
|
Outer: |
71x71x27mm |
Inner: |
67x67x23mm |
![]() |
PP100NBN |
![]() |
Features |
• Case for a remote-control transmitter • Comprising three case sections (upper, middle and lower) joined with a screw. • Upper and lower case sections in black, middle case section in blue • Middle case section comes with one pressbutton with approx. 2mm travel, e.g. for actuation of a microswitch underneath (not included in delivery). • For 12V battery • LED aperture |
![]() |
Note |
You will find suitable tact switches in this catalogue from product group E3331 on. You will find suitable battery GP-23A in our red "Components & Devices" catalogue in product group S1138. You will find suitable LEDs in our green "Semiconductors" catalogue fron product group W1222. |
![]() |
Terms of Delivery |
Minimum order quantity: 1 PKU = 1 piece |
![]() |
Manufacturer |
SUPERTRONIC http://www.supertronic.com |
![]() |