JavaScript seems to be disabled in your browser.

You must have JavaScript enabled in your browser to utilize the functionality of this website. Click here for instructions on enabling javascript in your browser.

ABS Enclosure 71x71x27 White

Varenummer:86-635
Varekode:PP42WS
Vægt:40.0g
Lagervare!
Henter lager-information...
Henter lager-information fra leverandører...
Internet-pris
Inkl. moms
Kr. 35,44
v/10Kr. 29,53
v/25Kr. 23,63
v/100Kr. 20,08

PP42WS ABS Enclosure 71x71x27 White PP42WSPP42WS ABS Enclosure 71x71x27 WhitePP42WS ABS Enclosure 71x71x27 White PP42WSPP42WS ABS Enclosure 71x71x27 White PP42WS
Produkt: Boks
Længde: 71mm
Bredde: 71mm
Højde: 27mm
Farve: Hvid
Materiale: Plastik
Gruppe: G4117
SUPERTRONIC ABS Miniature Enclosures
Series: PP
Colours: Black, White

PP12SW
Features
• Hand-held enclosure consisting of two shell halves
• Lap joint construction
• Two lateral guides (stud and bushing) are used to connect both shell halves.
• Two cams for self-tapping screws where a printed circuit can be mounted.
PP22SW
Transmission Receipt Enclosure for a Remote Control
Features
• Consisting of two shell halves which snap together to connect.
• Lap joint construction.
• 12V-Battery is required. (GP-23A is suitable and available in our "Components & Devices" catalogue at product group S1138)
• The printed circuit is fastened without screws onto a molded stud.
• In the upper section, there is a countersunk keypad.
• A button actuator is included which lies adjacent to an opening for a LED (You will find suitable LEDs in our Semiconductors catalogue at product group W1222).
• The firmly attached plastic button has a stroke of approx. 2mm, e.g. for operating a microswitch which is beneath (not supplied in the delivery).
Dimensions
Outer:
57x36x16mm
Inner, (Usable)1):
42x32x9mm
1) Including Battery Compartment for Round Cells, Contacts are Attached Loosely
PP23SW
Features
• Similar to PP12SW, but with 4 screws composed of stud and bushing placed in the corner to connect both shell halves
PP24SW
Transmission Receipt Enclosure for a Remote Control
Features
• Similar to PP22SW but with two button actuators lying adjacent to each other (black/red) and an opening above for a LED
Dimensions
Outer:
57x36x16mm
Inner (Usable)1):
42x32x9mm
1) Including Battery Compartment for Round Cells, Contacts are Attached Loosely
PP40SW
Features
• Black enclosure made of ABS
• Lid and base are attached using two studs.
• Fastening point for printed circuit
Dimensions
Outer:
50x36x20mm
Inner:
46x33x16mm
PP41SW
Features
• Black enclosure made of ABS consisting of base and lid
• Four countersunk screws seal the housing all around.
• Four mounting studs for a printed circuit 82x46mm
Dimensions
Outer:
100x50x25mm
Inner:
96x46x21mm
PP42WS
Features
• White sensor enclosure made of ABS
• Large louvered plates on either side
• Fastening points for printed circuit
Dimensions
Outer:
71x71x27mm
Inner:
67x67x23mm
PP100NBN
Features
• Case for a remote-control transmitter
• Comprising three case sections (upper, middle and lower) joined with a screw.
• Upper and lower case sections in black, middle case section in blue
• Middle case section comes with one pressbutton with approx. 2mm travel, e.g. for actuation of a microswitch underneath (not included in delivery).
• For 12V battery
• LED aperture
Note
You will find suitable tact switches in this catalogue from product group E3331 on.
You will find suitable battery GP-23A in our red "Components & Devices" catalogue in product group S1138.
You will find suitable LEDs in our green "Semiconductors" catalogue fron product group W1222.
Terms of Delivery
Minimum order quantity: 1 PKU = 1 piece
Manufacturer
SUPERTRONIC
http://www.supertronic.com