ABS Enclosure 71x71x27 White

Varenummer:	86-635
Varekode:	PP42WS
Vægt:	40.0g

Lagervare!

Henter lager-information...

Henter lager-information fra leverandører...

Internet-pris

Inkl. moms
	Kr. 35,44
v/10	Kr. 29,53
v/25	Kr. 23,63
v/100	Kr. 20,08

PP42WS ABS Enclosure 71x71x27 White PP42WS

Produkt:	Boks
Længde:	71mm
Bredde:	71mm
Højde:	27mm
Farve:	Hvid
Materiale:	Plastik

Gruppe: G4117
SUPERTRONIC ABS Miniature Enclosures
Series: PP
Colours: Black, White

PP12SW

Features

• Hand-held enclosure consisting of two shell halves
• Lap joint construction
• Two lateral guides (stud and bushing) are used to connect both shell halves.
• Two cams for self-tapping screws where a printed circuit can be mounted.

PP22SW

Transmission Receipt Enclosure for a Remote Control

Features

• Consisting of two shell halves which snap together to connect.
• Lap joint construction.
• 12V-Battery is required. (GP-23A is suitable and available in our "Components & Devices" catalogue at product group S1138)
• The printed circuit is fastened without screws onto a molded stud.
• In the upper section, there is a countersunk keypad.
• A button actuator is included which lies adjacent to an opening for a LED (You will find suitable LEDs in our Semiconductors catalogue at product group W1222).
• The firmly attached plastic button has a stroke of approx. 2mm, e.g. for operating a microswitch which is beneath (not supplied in the delivery).

Dimensions



Outer:	57x36x16mm
Inner, (Usable)¹⁾:	42x32x9mm
¹⁾ Including Battery Compartment for Round Cells, Contacts are Attached Loosely

PP23SW

Features

• Similar to PP12SW, but with 4 screws composed of stud and bushing placed in the corner to connect both shell halves

PP24SW

Transmission Receipt Enclosure for a Remote Control

Features

• Similar to PP22SW but with two button actuators lying adjacent to each other (black/red) and an opening above for a LED

Dimensions



Outer:	57x36x16mm
Inner (Usable)¹⁾:	42x32x9mm
¹⁾ Including Battery Compartment for Round Cells, Contacts are Attached Loosely

PP40SW

Features

• Black enclosure made of ABS
• Lid and base are attached using two studs.
• Fastening point for printed circuit

Dimensions



Outer:	50x36x20mm
Inner:	46x33x16mm

PP41SW

Features

• Black enclosure made of ABS consisting of base and lid
• Four countersunk screws seal the housing all around.
• Four mounting studs for a printed circuit 82x46mm

Dimensions



Outer:	100x50x25mm
Inner:	96x46x21mm

PP42WS

Features

• White sensor enclosure made of ABS
• Large louvered plates on either side
• Fastening points for printed circuit

Dimensions



Outer:	71x71x27mm
Inner:	67x67x23mm

PP100NBN

Features

• Case for a remote-control transmitter
• Comprising three case sections (upper, middle and lower) joined with a screw.
• Upper and lower case sections in black, middle case section in blue
• Middle case section comes with one pressbutton with approx. 2mm travel, e.g. for actuation of a microswitch underneath (not included in delivery).
• For 12V battery
• LED aperture

Note

You will find suitable tact switches in this catalogue from product group E3331 on.
You will find suitable battery GP-23A in our red "Components & Devices" catalogue in product group S1138.
You will find suitable LEDs in our green "Semiconductors" catalogue fron product group W1222.

Terms of Delivery

Minimum order quantity: 1 PKU = 1 piece

Manufacturer

SUPERTRONIC
http://www.supertronic.com